List of signal cable/accessory

for digital linear gauge



Signal cable

Model name Length Sensor side Outer dimensions Counter side
Signal extension cable AA-8801
5 m BS/GS series
Linear gauge sensor

Illustration (A-8000 series signal cable)

cable extension from a sensor: 30 m max.
  Cable D5-UL:UL standard compliant

DG series
Gauge counter
AA-8802
10 m
AA-8803 20 m
AA-8804 30 m
Bending resistant signal extension cable*1 AA-8811 5 m BS/GS series Linear gauge sensor Illustration (A-8000 series signal cable)

cable extension from a sensor: 30 m max.

DG series Digital gauge counter
AA-8812 10 m
AA-8813 20 m
AA-8814 30 m
Conversion cable AA-8901 5 m GS-3813B
GS-3830B
AA8901/8902/8903/8904 DG-5100
AA-8902 10 m
AA-8903 20 m
AA-8904 30 m
Signal extension cable AA-8910 0.2 m BS/GS series Linear gauge sensor (excluding GS-3800B series) AA-8910 DG-5100
BCD cable AA-8101
3 m DG-4320/4340 Gauge counter

Illustration (AA-8101 Signal cable)

DA-4130
DA converter
Discontinued
AA-8107
3 m DG-2310
4320/4340
Gauge counter

Illustration (AA-8107 signal cable)

-

Power supply cable AX-2050N
3 m DG-4320/4340/
5100 Gauge counter
DA-4130 Discontinued

Illustration (AA-2050 Signal cable)

*for 100 VAC

-

RS-232C cable AX-5022 2 m DG-2310
Gauge counter
PC
Signal cable MX-7105 5 m DG-0010
Output signal conversion box


Cable D5-UL:UL standard compliant

Open collector output

 

MX-7110 10 m
MX-7115 15 m
MX-7120 20 m
Extension by 5 m
(25 m to 30 m)
Made to order
Signal cable Made to order 30 m to
1200 m
DG-0020
Output signal conversion box
Line driver output

*1: Do not use/store cables under the environment at 0 °C or less. (Even though storage temperature of sensors used with is from -10℃ or more.)

*2: DX30A-36P is a crimping type connector. A tool for crimping type is required for wiring.
     Soldered type connector (DX40-36P, DX36CV1) is recommenced when you buy a connector.

Mechanical release

Outer Dimension

Applicable gauge sensor Model name

GS-251/251W

AA-812
Discontinued

Illustration(AA-812 Mechanical release)

GS-201,GS-102
BS-102/102W/112/112W

HS-3412/3425

DG-525H/825/925*
AA-813

*Use with the AA-972 release lifter.

 

Finger lift

Outer Dimension

Applicable gauge sensor Model name
For all models
(except for BS series )
AA-969 Illustration (AA-969 Finger lift)

Lift lever / Release lifter

Outer Dimension

Applicable gauge sensor Model name  
DG-525H/825/925 AA-971 Illustration (AA-971 Lift lever)
DG-525H/825/925
(Release is sold separately.)
AA-972 Illustration (AA-972 Release lifter)

Air lifter

Applicable gaige sensor Model name  
GS-1713/1813/
6713/6813/
4713/4813/
3813
AA-6102
*2 *3

GS-1730/1830/
6730/6830/
4730/4830
/3830

AA-6103
*2 *3

*1 Air lifter (AA-6100/6101) : not applicable to the protection class IP64,IP64G
*2 The AA-3102/3103 air lifter is required for an extension spindle. Full length becomes l22mm/37mm longer.
*3 It is required for air piping and electromagnetic valve for ON/OFF operation. The distance between sensor mounting surface and spindle sensor (9mm) is not changed.

Extension spindle(depth measurement for pin hole)

Outer Dimension

Extension length Model name  
30 mm AA-844 Illustration (AA-844 Extension spindle)
Material:SUS303 Diameter:φ 3.8 mm Thread part:M2.5
50 mm AA-845 Illustration (AA-845 Extension spindle)
Material:SUS303 Diameter:φ 3.8 mm Thread part:M2.5

Measurement tip

Outer Dimension

AA-0200 AA-0210 AA-0220 *1 AA-0230 AA-0240
Illustration (AA-0200 Measurement tip)

Material at a tip:steel ball

Illustration (AA-0210 Measurement tip)

Material:SKS3

Illustration (AA-0220 Measurement tip)

Material:SKS3

Illustration (AA-0230 Measurement tip)

Material:SKS3

Illustration (AA-0240 Measurement tip)

Material:SKS3

AA-0250 AA-0260
Discontinued
AA-827 *2 AA-828 *2 AA-0310
Discontinued
Illustration (AA-0250 Measurement tip)

Material:SKS3

Illustration (AA-0260 Measurement tip)

Material:SKS3

Illustration (AA-827 Measurement tip)

Material:SUj2

Illustration (AA-828 Measurement tip)

Material:SUj2

Illustration (AA-0310 Measurement tip)

Material at a tip:steel ball

AA-0320 AA-921 AA-0330
Made to order
AA-0400
Illustration (AA-0320 Measurement tip)

Material:SKS3

Illustration (AA-921 Measurement tip)

Material:SKS3

Illustration (AA-0330 Measurement tip)

Material of the ball at a tip:carbide

Illustration (AA-0400 Measurement tip)

Material of the ball at a tip:ruby

*1 When mounting a flat measurement tip such as AA-0220/0240/0250 to a gauge sensor with a measurement resolution of 1/1000mm (1 µm ), adjustment of the degree of parallelization to match that of the surface of the measurement stand is required. In this case, the measurement tip and gauge stand must be purchased as a pair.
*Accuracy after parallelization adjustment by us: approx. 10 µm
*2 When mounting a roller measurement tip such as AA-827/828 etc to a gauge sensor with a measurement resolution of 1/1000mm (1 µm), the accuracy described its specification is not obtained.
The AA-827/828 uses a bearing, but as the gap cannot be eliminated, an error of approximately 10µm may appear.

 

 

Joint measurement tip adapter (for replacement of mesurement tip)

Applicable gauge sensor Model name

GS-102/251/503/1000 AA-829
Made to order
Illustration (AA-829 Joint measurement tip adapter)Material:C36002

Dust proof rubber

Outer Dimension

Applicable gauge sensor Model name L1
(mm)
External diameter of collar
(φ mm)
External diameter of rubber
(φ mm)
Stem diameter
(φ mm)
Material *3
GS-1000 AA-841 *1 40.5 22 24 15 CR
BS-102/102W/
112/112W
AA-973 *1 - - 8 8 EPM
GS-5011 AA-975 *2 8.5 - 16 20 NBR
GS-1513A/1613A/
6513/6613
AA-4100 - - 8 8 Si
GS-4513/4613/
4530/4630 *4
Made to order
*5
- - 10 10 Si
GS-1713/1813/
6713/6813
AA-4102 - - 8 15 Si
GS-1730/1830/
6730/6830
AA-4103 - - 8 15 Si
GS-4713/4813/
3813
AA-4104 - - 8 15 HNBR
GS-4730/4830/
3830
AA-4105 - - 8 15 HNBR
*1 Provided the measurement tip for dust proof rubber as standard. (Refer to the following drawing for outer dimensions.)
*2 Provided the joint for dust proof rubber as standard. (Refer to the above and following drawings for outer dimensions.)
*3 CR:Chloroprene rubber, NBR:nitrile rubber, EPM:Ethylene-propylene rubber, Si:silicon rubber, HNBR:hydrogenated nitrile rubber
*4 Dust-proof rubber for the GS-4500/4600 series (material:fluorine rubber) is made to order. (For the replacement, please return us a product.)
*5 The installation is required by Ono Sokki. (Delivery cost may be charged separately.)

AA-841 With the measurement tip for dust-proof rubber
for BS series, GS-1000
Illustration (AA series Dust-proof rubber)
AA-829 Measurement tip adapter
for GS-102/251/503/1000

The AA-829 measurement tip adapter is required when the special measurement tip and dust-proof rubber are used with.

AA-975 With the joint for dust-proof rubber for GS-5011

Please attach the AA-975 (joint for dust-proof rubber) directly when the special measurement tip is used with. The joint for the special measurement tip is no required.

Mounting fixture

Applicable gauge sensor Model name  
GS-5050/5051/5100/5101 AA-8560 Illustration (AA-855 Mounting fixture)
GS-1713/1730/1813/1830
GS-3813/3830/4713/4730
GS-4813/4830/6713/6730
GS-6813/6830
AA-3310 Illustration (AA-3300 Mounting fixture)

Gauge stand

Model name of gauge stand ST-022 ST-0230 ST-044B
Applicable gauge

gauge sensor

BS-1210 *1
BS-1310 *1
GS-7710A *1
GS-7710NA *1
GS-1713A/1730A
GS-1813A/1830A
GS-3813B/3830B
GS-4713A/4730A
GS-4813A/4830A
GS-6713A/6730A
GS-6813A/6830A
GS-5050A/5100A
GS-5051A/5101A
reference

Stem D. Φ8 mm

Stroke 10 mm

Stem D. Φ15 mm
Stroke 13/30 mm
Stem D. Φ15 mm
Stroke 50/100 mm
Table dimension (mm) 80 × 85 105 × 105
Diameter of mounting hole Φ8 to 10 Φ15 Φ15 to 20
Table material Ceramic (with groove)
Flatness of measuring surface 1 µm
Roughness of measuring surface 0.4 S Lapping finish
Base stand (Width×Depth mm) 100 ×160 130 × 200
Measurable depth (mm) approx. 59 approx. 60 approx. 73.5
Measurable height (mm) approx. 115 approx. 210
Weight 4.1 kg 4.2 kg 7.5 kg
*1 The stand bush AA-891 (for φ8 mm) or AA-892 (for φ10 mm) is required when attaching the ST-0230 or ST-044B to a linear gauge sensor (stem diameter of φ 8 mm or φ10 mm).

 



Knob (A): for attachment and removal from the gauge sensor

Knob (B) and (C): vertical adjustment of stand (shaft)

Illustration (ST series Gauge stand)

 

Accuracy of gauge stand

The outer dimensions of the SH-022 and ST-022 are same, but the accuracy of its squareness and parallelism is different.

 

When attaching a flat measurement tip such as the AA-0220/0240/0250/921 to a gauge with a measurement resolution of 0.05µm/1µm, adjustment of the degree of parallelization to match that of the surface of the measurement stand is required. In this case, the measurement tip and stand must be purchased as a pair (additional cost required). The accuracy of the parallelization is 10µm or less. Please contact your nearest distributor or mail to us overseas@ONO SOKKI.co.jp.

Backup supply / Consumable goods

Model name Product name Purpose
R03-PB6M Connector for gauge sensor signal -
57-30360 36-core connector (for BCD signal cable)

RQ-1410Discontinued

DX40-36P 36-core connector for cable, for BCD signal, for soldered (DX36CV1 is required)

DG-4120/4140/4240/4280
DA-4130Discontinued

DX36CV1 Plug cover for DX36CV1

DX40-36P

TA2096
Adapter for AC power supply (cable: approx. 1.8 m)
Input: AC 100 V, Output: DC 9 V/300 mA
DG-525H/825/925
AA-5100 Thermal recording paper (10-roll / pack)

RQ-1410

Revised:2023/07/06



webinfo

 

Copyright © ONO SOKKI CO.,LTD All Rights Reserved. | Terms of use | Privacy policy