Linear Gauge Sensors
GS series
Specification table for Linear Gauge Sensors (Click)
General purpose, dust-proof and splash-proof IP64
• Replaces with the GS-1500/1600 series
• Using ball bearing increases the maximum number of sliding times of the spindle compared with the existing model.
Specifications
| Model name Item |
GS-1713A | GS-1730A | GS-1813A | GS-1830A |
|---|---|---|---|---|
| Measurement range | 13 mm | 30 mm | 13 mm | 30 mm |
| Resolution | 10 μm | 1 μm | ||
| Accuracy (at 20 °C) | 3 μm | 3 μm | 2 μm | 3 μm |
| Maximum spindle velocity*1 | 1(4) m/s | 0.3(1.2) m/s | ||
| Measurement force(downward)*2 | 1.3 N or less | 1.9 N or less | 1.3 N or less | 1.9 N or less |
| Number of sliding times (proven in our endurance test) |
6.5 million times or more | |||
| Protection class (not including connector part) |
IP64 | |||
| Stem diameter | Ø15 mm+0-0.009 | |||
| Power supply | 4.5 to 5.5 VDC | |||
| Power consumption (5 VDC) | 120 mA or less | |||
| Signal output (5 VDC) | Two-phase square wave, phase difference: 90° ± 20° |
|||
| Output impedance | Approx. 22 Ω | |||
| Vibration resistance (when the power is off) *3 |
98 m/s2 in each of the three axial directions (75 minutes per each), 10 cycles of 10 Hz to150 Hz sweeping |
|||
| Shock resistance (when the power is off)*3 |
980 m/s2 in each of direction for each of three axex, three times for each of ±X,Y and Z directions, sine half-wave, pulse duration 6 ms |
|||
| Operating temperature range | 0 to +40 °C | |||
| Storage temperature range | -10 to +55 °C | |||
| Cable length | Approx. 1.9 m | |||
| Weight (including cable, connector) | Approx. 250 g | Approx. 310 g | Approx. 250 g | Approx. 310 g |
| Accessories | Instruction manual, spanner | |||
*1. When used with Ono Sokki's Gauge Counter. The values within parentheses () is the maximum spindle velocity used with the DG-4140/DG-4190/DG-5100/DG-3000.
*2. An attachment may not return completely if it is facing upwards.
*3 Vibration/shock resistance values described in above are not guaranteed during measurement operation.
• Disconnected or modified signal cable is not applicable to CE marking.
NOTE:Please check an attaching portion (material, grounding etc.) before you install the New GS series. If the New GS series is installed in a metallic portion that is not grounded, it might cause blowout of a fuse or cable damage because of a potential difference that might be produced between a counter side chassis and a sensor side chassis.
Vibration resistant structure, dust-proof and splash-proof structure IP64
• Replaces with the GS-6500/6600 series
• Bonded anchorage of electric parts gives better performance of vibration resistance.
• Using ball bearing increases the maximum number or sliding times of the spindle compared with the existing model.
Specifications
| Model name Item |
GS-6713A | GS-6730A | GS-6813A | GS-6830A |
|---|---|---|---|---|
| Measurement range | 13 mm | 30 mm | 13 mm | 30 mm |
| Resolution | 10 μm | 1 μm | ||
| Accuracy (at 20 °C) | 3 μm | 3 μm | 2 μm | 3 μm |
| Maximum spindle velocity*1 | 1(4) m/s | 0.3(1.2) m/s | ||
| Measurement force(downward)*2 | 1.3 N or less | 1.9 N or less | 1.3 N or less | 1.9 N or less |
| Number of sliding times (proven in our endurance test) |
6.5 million times or more | |||
| Protection class (not including connector part) |
IP64 | |||
| Stem diameter | Ø15 mm+0-0.009 | |||
| Power supply | 4.5 to 5.5 VDC | |||
| Power consumption (5 VDC) | 120 mA or less | |||
| Signal output (5 VDC) | Two-phase square wave, phase difference: 90° ±20° |
|||
| Output impedance | Approx. 22 Ω | |||
| Vibration resistance (when the power is off)*3 |
147 m/s2 in each of the three axial directions (75 minutes per each), 10 cycles of 10 Hz to150 Hz sweeping |
|||
| Shock resistance (when the power is off)*3 |
1470 m/s2 in each direction for each of three axes, three times for each of the ±X,Y and Z directions, sine half-wave, pulse duration 6 ms |
|||
| Operating temperature range | 0 to +40 °C | |||
| Storage temperature range | -10 to +55 °C | |||
| Cable length | Approx. 1.9 m | |||
| Weight (including cable, connector) | Approx. 250 g | Approx. 310 g | Approx. 250 g | Approx. 310 g |
| Accessories | Instruction manual, spanner | |||
*1. When used with Ono Sokki's Gauge Counter. The values within parentheses () are the maximum spindle velocity used with the DG-4140/DG-4190/DG-5100/DG-3000.
*2. An attachment may not return completely if it is facing upwards.
*3. Vibration/shock resistance values described in above are not guaranteed during measurement operation.
• Disconnected or modified signal cable is not applicable to CE marking.
NOTE:Please check an attaching portion (material, grounding etc.) before you install the New GS series. If the New GS series is installed in a metallic portion that is not grounded, it might cause blowout of a fuse or cable damage because of a potential difference that might be produced between a counter side chassis and a sensor side chassis.
Vibration resistant structure, dust-proof, water-proof and oil-proof IP66G
Specifications
| Model name Item |
GS-4713A | GS-4730A | GS-4813A | GS-4830A |
|---|---|---|---|---|
| Measurement range | 13 mm | 30 mm | 13 mm | 30 mm |
| Resolution | 10 μm | 1 μm | ||
| Accuracy (at 20 °C) | 3 μm | 3 μm | 2 μm | 3 μm |
| Maximum spindle velocity*1 | 1(4) m/s | 0.3(1.2) m/s | ||
| Measurement force(downward)*2 | 1.8 N or less | 2.4 N or less | 1.8 N or less | 2.4 N or less |
| Number of sliding times (proven in our endurance test) |
15 million times or more | |||
| Protection class (not including connector part) |
IP66G | |||
| Stem diameter | Ø15 mm+0-0.009 | |||
| Power supply | 4.5 to 5.5 VDC | |||
| Power consumption (5 VDC) | 120 mA or less | |||
| Signal output (5 VDC) | Two-phase square wave, phase difference: 90° ±20° |
|||
| Output impedance | Approx. 22 Ω | |||
| Vibration resistance (when the power is off)*3 |
196 m/s in each of the three axial directions (75 minutes per each), 10 cycles of 10 Hz to150 Hz sweeping |
|||
| Shock resistance (when the power is off)*3 |
1960 m/s2 in each direction for each of three axes, three times for each of ±X,Y and Z directions, sine half-wave, pulse duration 6 ms |
|||
| Operating temperature range | 0 to +40 °C | |||
| Storage temperature range | -10 to +55 °C | |||
| Cable length | Approx. 4.9 m | |||
| Weight (including cable, connector) | Approx. 325 g | Approx. 385 g | Approx. 325 g | Approx. 385 g |
| Accessories | Instruction manual, spanner | |||
*1. When used with Ono Sokki's Gauge Counter. The values within parentheses () is the maximum spindle velocity used with the DG-4140/DG-4190/DG-5100/DG-3000.
*2. An attachment may not return completely if it is facing upwards.
*3. Vibration/shock resistance values described in above are not guaranteed during measurement operation.
• Disconnected or modified signal cable is not applicable to CE marking
NOTE:Please check an attaching portion (material, grounding etc.) before you install the New GS series. If the New GS series is installed in a metallic portion that is not grounded, it might cause blowout of a fuse or cable damage because of a potential difference that might be produced between a counter side chassis and a sensor side chassis.
Long Stroke type
Specifications
| Model name Item |
GS-5050A | GS-5100A | GS-5051A | GS-5101A |
|---|---|---|---|---|
| Measurement range | 50 mm | 100 mm | 50 mm | 100 mm |
| Resolution | 10 μm | 1 μm | ||
| Accuracy (at 20 °C) | 10 μm | 12 μm | 4 μm | 5 μm |
| Maximum spindle velocity*1 | 1(4) m/s | 0.3(1.2) m/s | ||
| Measurement force(downward)*2 | 2.9 N or less | 5.2 N less | 2.9 N or less | 5.2 N or less |
| Number of sliding times (proven in our endurance test) |
15 million times | |||
| Protection class (not including connector part) |
IP5X | |||
| Stem diameter | Ø15 mm+0-0.009 | |||
| Power supply | 4.5 to 5.5 VDC | |||
| Power consumption (5 VDC) | 120 mA or less | |||
| Signal output (5 VDC) | Two-phase square wave, phase difference: 90° ±20° |
|||
| Output impedance | Approx. 22 Ω | |||
| Vibration resistance (when the power is off)*3 |
147 m/s2 in each of the three axial directions (75 minutes per each), 10 cycles of 10 Hz to150 Hz sweeping |
|||
| Shock resistance (when the power is off)*3 |
1470 m/s2 in each of direction for each of three axes, three times for each of ±X,Y and Z directions, sine half-wave, pulse duration 6 ms | |||
| Operating temperature range | 0 to +40 °C | |||
| Storage temperature range | -10 to +55 °C | |||
| Cable length | Approx. 4.9 m | |||
| Weight (including cable, connector) | Approx. 570 g | Approx. 655 g | Approx. 570 g | Approx. 655 g |
| Accessories | Instruction manual, spanner | |||
*1. When used with Ono Sokki's Gauge Counter. The values within parentheses () are the maximum spindle velocity used with the DG-4140/DG-4190/DG-5100/DG-3000.
*2. An attachment may not return completely if it is facing upwards.
*3. Vibration/shock resistance values described in above are not guaranteed during measurement operation.
• Disconnected or modified signal cable is not applicable to CE marking.
NOTE:Please check an attaching portion (material, grounding etc.) before you install the New GS series. If the New GS series is installed in a metallic portion that is not grounded, it might cause blowout of a fuse or cable damage because of a potential difference that might be produced between a counter side chassis and a sensor side chassis.
The number of sliding times: 5 million →15 million
Protection class: IP64 → IP66G
Vibration resistance: 98 m/s2 →196 m/s2
Shock resistance: 980 m/s2 →1960 m/s2
Specifications
| Model name Item |
GS-3813B | GS-3830B |
|---|---|---|
| Measurement range | 13 mm | 30 mm |
| Applicable counter | DG-5100 | |
| Resolution | 0.1 μm | |
| Accuracy (at 20 °C) | 1 μm | |
| Maximum spindle velocity*1 | 300 mm/s (1.2 m/s) | |
| Measurement force(downward)*2 | 2.3 N or less | 2.7 N or less |
| Number of sliding times (proven in our endurance test.) | 15 million times or more | |
| Protection class(not including connector part) | IP66G | |
| Stem diameter | φ15 mm+0 -0.009 | |
| Power supply | 4.5 to 5.5 VDC | |
| Power consumption (5 VDC) | 150 mA or less | |
| Signal output (5 VDC) | 90 degree phase-differential square wave Applicable to RS422A Line driver output(equivalent to 26C31) |
|
| Vibration resistance (when the power is off)*3 |
196 m/s2 in each of the three axial directions(75 minutes per each), 10 cycles of 10 Hz to150 Hz sweeping |
|
| Shock resistance (when the power is off)*3 |
1960 m/s2 in each of the three axial directions. Three times each in the ±X,Y,Z directions, sine half-wave, pulse duration 6 ms |
|
| Operating temperature range | 0 to +40 °C | |
| Storage temperature range | -10 to +55 °C | |
| Cable length | Approx. 5 m | |
| Weight (including cable, connector) | Approx. 350 g | Approx. 420 g |
| Accessories | Instruction manual, spanner | |
*1. When used with Ono Sokki’s Gauge Counter. The values within parentheses () are the maximum spindle velocity used with the DG-5100.
*2. An attachment may not return completely if it is facing laterally or upwards.
*3. Vibration/shock resistance values described in above are not guaranteed during measurement operation.
• Disconnected or modified signal cable is not applicable to CE marking.
NOTE:Please check an attaching portion (material, grounding etc.) before you install the New GS series. If the New GS series is installed in a metallic portion that is not grounded, it might cause blowout of a fuse or cable damage because of a potential difference that might be produced between a counter side chassis and a sensor side chassis.
Revised:2021/06/02
