| Torque
Measurement Section |
Input
Section |
Input signal |
Phase-differential type torque detectors |
|
Connector |
TRC116-12A10-7M10.5 or
CO2 (BNC) plug x 2 (not available to use at same time) |
| Condition
Setup Section |
Capacity |
±1 to 9999 |
| Factor |
1 to 65535 |
| Unit |
mNm, Nm, kNm |
| Zero
compensation |
1 point
each for CW & CCW
manual or automatic operation |
| N-0
compensation |
10 points
each for CW & CCW
manual or automatic operation |
|
Rotational direction |
CW, CCW, EXT |
|
Response |
Time constant can be settable among;
16ms/31ms/63ms/125ms/250ms/500ms/1s/2s/4s/8s/16s/32s/64s |
| Display
Section |
Digit |
polarity + 4-digit or 5-digit, selectable |
|
Display updating |
1s to 10s (settable, at 1s step) or timing
of external input signal |
| Accuracy |
with N-0 compensation |
±0.2 % / FS ±1 count
(when 4-digit display, at 1s updating) |
| without
N-0 compensation |
±0.5 % / FS ±1 count
(when 4-digit display, at 1s updating) |
| Output
Section |
Analog
output |
Voltage signal,
0±10V / F.S |
| Scale |
Settable at 0.1V step for 0.1 to 10V |
|
Response |
16ms to 64s
specified by time constant |
|
Accuracy |
with N-0 compensation |
±0.2 % / FS (averaged value for one
second) |
| without
N-0 compensation |
±0.5 % / FS (averaged value for one
second) |
|
Temperature drift |
±0.01 % / FS / °C |
|
Connector |
CO2 (BNC) plug |
|
Revolution Measurement Section |
Input Section |
REVO1 |
Type |
Sine wave input
(ex., MP-910 Magnetic Detector) |
| Input Impedance |
10Ω min. |
| Frequency |
10 Hz to 100 kHz |
| Amplitude |
0.2 to 45 Vrms |
| Connector |
CO2 (BNC) plug |
|
REVO2 |
Type |
Square wave input
(ex., MP-981 electroMagneto-electric rotation detector) |
| Input Impedance |
10Ω min. |
| Frequency |
1 Hz to 200 kHz |
| Amplitude |
Hi : +4 to +30V, Lo : +0.6Vmax
pulse width : 2us min |
| Power Supply |
DC 12V, 100mA
(for electroMagnetic Detector) |
| Connector |
CO2 (BNC) plug |
| INT |
Type |
SIG2 input of torque signal |
| Condition
Setup Section |
Unit |
r/min, r/s, Hz |
Pulse
Selection of
Signal Input from Rev. pickup |
1 to 99999 P/R |
|
Gear Ration |
±1 to 9999/1 to 9999
available to display at revolution before change of speed |
|
Offset |
±1 to 9999
only available when r/min unit is selected
Measured value = actual measured value - off set value |
|
Response |
Time constant can be settable among;
16ms/31ms/63ms/125ms/250ms/500ms/1s/2s/4s/8s/16s/32s/64s |
| Display
Section |
Digit |
5-digit |
|
Display resolution |
0.001/0.01/0.1/1, available to select
through capacity (full scale) setup |
|
Display updating |
1s to 10s (settable, at 1s step) or timing
of
external input signal
(same as torque section) |
|
Accuracy |
±0.05 % / FS ±1 count
(at 1s updating) |
| Output
Section |
Analog
output |
Voltage signal,
0±10V / F.S |
| Scale |
Settable at 0.1V step for 0.1 to 10V |
|
Response |
16ms to 64s
specified by time constant |
|
Accuracy |
(averaged value for one second) ±0.1 % / FS |
|
Temperature drift |
±0.01 % / FS / °C |
|
Connector |
CO2 (BNC) plug |
|
Output/Power Calculation Section |
Power |
Calculation |
Output power (W) =
torque (Nm) x rev. speed (r/min) x 2π/60
1 PS = 0.7355 kW |
|
Display Section |
Digit |
polarity + 5-digit |
|
Display updating |
1s to 10s (settable, at 1s step) or timing
of
external input signal
(same as torque section) |
|
Unit |
mW, W, kW, PS |
|
Accuracy |
Accuracy of torque display + accuracy of
revolution display |
| Output
Section |
Analog
output |
Voltage signal,
0±10V / F.S |
| Scale |
Settable at 0.1V step for 0.1 to 10V |
|
Response |
16ms to 64s
specified by time constant |
|
Accuracy |
Accuracy of torque display + accuracy of
revolution display |
|
Temperature drift |
±0.01 % / FS / °C |
|
Connector |
CO2 (BNC) plug |
|
Display Panel |
LCD |
320 x 240 dots |
| Backlight |
ON/OFF, selectable |
| Main |
Single/Dual/Triple display, selectable among
torque, revolution, power (output) |
| Sub |
Can be combined with Main Display function
peak values (MAX/MINI/P-P), ripple ratio |
| Status |
READY, CLEAR, TRQ IN, REV IN,
CW/CCW, CMP OUT ON/OFF |
|
Interface Section |
Remote
Control |
Clear Input |
Contact input
display and output is forced to be zero(0) when contact is closed. |
| Revolution
Direction Input |
Contact input
selection of torque zero point at CW/CCW
CCW selected when contact is closed. |
| Trigger
Input |
Contact input
Status of display and BCD is updated
by contact being closed when external gate activated, or by pressing a switch on the panel when trigger function activate. |
| Trigger
Output |
Contact output
synchronized with gate timing
ex. when 1s gate, 0.5s on / 0.5s off |
| Ready
Output |
Contact output
contact closed when TS-3200 under torque measurement |
| Input
Section |
Type |
Dry contact input |
| Contact
Input |
Voltage : 5.25V max.
Current : 1mA max. |
| Voltage
Input |
Hi level : +4 to +5.25V
Lo level : 0 to +1V |
| Output
Section |
Type |
Photo-MOS relay |
| Withstand
voltage |
DC30V max. |
| Withstand
current |
100mA max. |
| Resistor (ON) |
10Ω max |
| Resistor
(OFF) |
500kΩ min. |
| Connector |
R03-PB8M |
|
Analogue Voltage Output |
No. of
output channel |
No. of
output channel |
| Parameter |
2 items can be selected among torque, revolution or power |
| Connector |
CO2 (BNC) plug |
|
Specification |
See descriptions of "Output Section"
for each measuring parameter |
Comparator Output
opt.
TS-0322 |
No. of
output channel |
2 channels |
| Parameter |
Upper or lower of torque, revolution or power (output) |
| Output
updating |
Settable between 0.004 to 10s or external |
| Comparison |
Activated by averaged value in setup time |
| Output
method |
Same as function of Output Section in Remote Control |
| Connector |
RM12BPE-4S |
BCD Output
opt.
TS-0323 |
No. of
output channel |
2 channels |
| Parameter |
Selectable among torque, revolution or power |
| Output
updating |
at gate timing between 0.1 to 10s or external, or
at every sampling time |
| Output
method |
Positive logic
open collector output |
| Connector |
57-30500 (DDK) amphenol
full pitch with 50-pin |
RS-232C
opt.
TS-0325 |
Standard |
complied to EIA and JISX5101 |
| Baud rate |
1200/2400/4800/9600/19200 bps |
| Connector
|
D-sub 9-pin, female |
GP-IB
opt.
TS-0326 |
Standard |
complied to IEEE488-1978 |
|
General |
Power Supply |
AC100 to 240V ±10 % 50/60 Hz |
|
Power Consumption |
35VA max. |
|
Insulation Resistor |
10MΩ min. at DC500V |
|
Withstanding Voltage |
AC1500V for 1 min. |
| Operating
Temperature |
0 to +40°C |
|
Storage Temperature |
-10 to +55°C |
| Outer
dimensions |
approx. 376 (W) x 114 (H) x
317.2
(D) mm |
| Weight |
Approx. 5 kg |
